Understanding Essential Plumbing Skills is Vital for Installing a Bathtub
Understanding Essential Plumbing Skills is Vital for Installing a Bathtub
Blog Article
This great article which follows about A Step-by-Step Guide to Installing a Bathtub is truly enjoyable. Don't skip it.
Installing a bath tub isn't specifically rocket science, however it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old tub with a new one is also a reasonably hard task. If the old bathtub is easily easily accessible, the task can move quickly; if you have to open up a wall to eliminate the old tub and also position the new tub, the task is much harder. In either case, the project is within a residence handyman's skills, although you will require a helper to vacate the old tub as well as embeded in the new one. Make sure you have qualified on your own for the task and also are comfortable trying it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to think about employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This short article will assist you mount a brand-new bath tub in your restroom if you have currently acquired a brand-new tub and do not need to transform the setup of your previous supply of water pipelines.
Your tools and also product checklist need to make up the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of eliminating the existing faucets can be rather troublesome as a result of the restricted accessibility that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washers remain in area between the tap as well as the sink. Protect the faucet in place with the manufacturer offered backnut. When the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The previous type should be linked to the faucet finishes initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Using both wood boards under its feet, place the bath tub in the required setting. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and also adjusting the feet on the bath tub till the level reviews degree.
To set up taps, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Switch on the supply of water and also examine all joints as well as brand-new pipework for leaks and also tighten them if required. Fill the bathtub as well as likewise check the overflow electrical outlet and also the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bathtub should wait till the bathtub has been made use of at least when as this will certainly settle it into its last position.
Preparing for the Setup
First of all, the sustaining structure provided with the bathroom must be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to stop stress on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last position.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to split a rigid seal, creating the water to permeate the wall surface in between the bathroom and also the tiling, resulting in complications with dampness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, and also can securing voids as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealant can fracture rather very early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly readily available on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or water-proof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our excerpt about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a ton for finding the time to read through our short article. Enjoyed reading our posting? Please share it. Help others find it. We cherish reading our article about Tools You Need to Install a New Bathtub .
Leak-free future? Call. Report this page